Speedway Series 7117 125 Amp 110 Volt Single
Model: FW125ABrand: SpeedwayRegular Price: $139.99Discount Price: $139.99
Average Customer Rating
4 out of 5
- Self regulating feed control
- Thermal protection with warning light
- Input: 110volt, single phase
- Wire capacity: 0.035 or 0.030
- No Gas Needed
This flux core welder handles .023, .030 and .035in. wires and welds 18-gauge to 3/16in. steel. Self-regulating feed control; wire feed speed 0-400 IPM. Duty cycle: 10% @ 90 Amp, 19V; thermal protection with warning light. ....read more Discount Price:
$139.99Related Products
|
| Model: FW125A Brand: Speedway Regular Price: $139.99 Discount Price: $139.99 Average Customer Rating
|
- Self regulating feed control
- Thermal protection with warning light
- Input: 110volt, single phase
- Wire capacity: 0.035 or 0.030
- No Gas Needed
This flux core welder handles .023, .030 and .035in. wires and welds 18-gauge to 3/16in. steel. Self-regulating feed control; wire feed speed 0-400 IPM. Duty cycle: 10% @ 90 Amp, 19V; thermal protection with warning light. ....read more
Discount Price:
$139.99Related Products
welder
Rating:5 out of 5 stars
My son and daughter love this welder. He sold his huge one so he could enjoy something easier to handle, use, carry, and work with. This one gives him a lot of pleasure! I am so glad we found it online!
so far so good
Rating:4 out of 5 stars
first unit the motor didnt run to feed the wire through but they replaced it quick and were very helpful on the phone. after i got the second unit i set it up right away and tested the motor it ran fine. i used it on steel today and i think if i wasnt new to welding it would be great in other words any problem at this point is due to the user.
Speedway is a good Way
Rating:4 out of 5 stars
I’m 54 yrs old and have been welding since 1973.This little welder surprised me it is very well made and easy to operate /is great to teach with and it will melt 3/16 steel if you don’t keep it moving.Have not really tried the low side yet on anything thin but I have no doubt that it will be fine.I have ran 6 rolls of.35 wire so far and I have found it best to take tip out during spool change so it don’t cobble up at spool.Both of my local hardware stores carry the spool I use it is a 2pound 5/8 hole that this welder uses and tips are also easy to get a 10 pack is about $5. Seems to have slight problem finding hole in tip/goes through liner fine but when it gets to tip?? If you run high side you can weld about 7 to 8 minutes before heat light comes on and shuts you down but thats a long weld.And by the time you check what your doing grab a drink of what ever its ready to go again.
speedway welder
Rating:1 out of 5 stars
Wire feed mechanism quit working within the first five minutes.. I returned the unit it for refund.
Not working out of the box!!
Rating:1 out of 5 stars
The only plus is the item was shipped quickly. Although it doesn’t help when this did not even work out of the box! I sent it back for a refund.
My review
Rating:5 out of 5 stars
It was not to feed wire at all once I have received it opening box.
But satisfied with quick replacement with no hesitating as well as great performance of new one in welding work.
Great wire feeding welder at good price.
welder
Rating:2 out of 5 stars
the wire feeder on this welder doesn’t feed the wire very well I think it would be ok If I could get the wire to feed steady.
Great Value
Rating:5 out of 5 stars
I think this has to be the best purchase I have made in a long time .
this littel welder has amazed me ,if you are a do it your selfer and think you might need a welder I can rate this a must have for any tool collection!